Updated November 2026
An easyfit dual tower closet organization system 72″-120″ adjustable width gives you two vertical storage towers that span a closet of nearly any width within that range, letting you mount shelves, rods and drawers on both sides of an open center. In this guide you will measure your closet correctly, decide how to lay out the two towers, install the hardware in the right order and set up the interior so it stays tidy. The process takes a few hours for most closets, and the steps below assume you have basic hand tools and a helper for the taller pieces.
What the Dual Tower Format Does Well
A dual tower layout places one tower on each side wall, with the open space between them used for hanging rods, shoe ledges or a shared shelf. Because the towers are independent, you can put long hanging garments on one side and folded storage on the other without stacking everything on a single wall. This format works especially well in reach-in closets and narrow walk-ins where a single run of shelving would leave the ends unused.
Shopping for one? See our guide: Laundry Closet Organization Systems: 5 Best Picks for Every Space (2026).
The adjustable width matters because closets are rarely built to exact dimensions. Many reach-in closets fall somewhere between 72 and 120 inches wide once you account for trim, door swing and wall irregularities. An adjustable system lets you match the hardware to the real opening rather than forcing the closet to fit a fixed kit.
Step 1: Measure Your Closet Accurately
Before you open any boxes, measure the closet at three heights: near the floor, at the middle and near the top. Walls are often out of plumb, and a closet that measures 96 inches at the bottom may measure 95 inches at the top. Use the narrowest reading as your working width, and record the depth from the back wall to the door track or the front edge of the frame.
Next, measure the height from the floor to the ceiling and note any obstructions such as light fixtures, baseboard heaters or a ceiling-mounted access panel. Mark where the door swings, because the towers should not block the door’s arc. Finally, check whether the walls are drywall or plaster, since that determines the anchor type you will need.
Measurement Checklist
- Width at floor, middle and ceiling height (use the smallest figure)
- Depth from back wall to front edge of the frame
- Ceiling height and any fixtures that overlap the upper tower
- Door swing clearance on each side
- Wall material: drywall, plaster or masonry
- Stud locations marked with a stud finder
Step 2: Plan the Two Tower Layout
Decide what each tower will hold before you drill anything. A common plan uses the left tower for shelves and drawers, the center for a hanging rod and the right tower for shoe storage or additional shelves. If the closet is shallow, keep the towers deeper than the hanging space so garments do not catch on the uprights.
Sketch the layout on paper at a scale of 1 inch to 6 inches. Mark where the rod will sit, typically 40 to 42 inches from the floor for a single hanging rod in a standard closet, or around 66 to 70 inches for a full-length rod. Place shelves at heights that match what you store: taller bins near the bottom, frequently used items between 30 and 60 inches, and seasonal storage above that.
Step 3: Set the Width and Anchor the Towers
Adjust the cross-bars to your measured width, leaving a fraction of an inch of play so the towers can be slid into position without forcing them. Assemble each tower on the floor first, then stand it up with a helper. Check that each tower is plumb with a level before fastening.
Fasten the towers into studs wherever possible. Drywall anchors rated for the expected load are acceptable for light items, but a loaded tower should be attached to at least two studs per side. If the wall studs do not line up with the tower brackets, use a short wood spacer block on the stud to bridge the gap.
Tools and Supplies Needed
- Tape measure and pencil
- Stud finder and level
- Power drill with a bit set
- Screwdriver or drill driver for the hardware
- Wood spacer blocks, if studs are off-center
- Wall anchors rated for the load, for any areas without studs
Step 4: Install the Rod, Shelves and Drawers
Install the center rod after both towers are secure, so the rod brackets can be aligned against both uprights. Check the rod is level in both directions. Then add the shelves from the bottom up. Bottom shelves carry the most weight, so they should be the first to be fixed and tested.
If your system includes drawers, slide them in only after the tower is anchored and level. Drawers tend to rack out of square if the frame is not true, which causes them to stick. Test each drawer glide before loading it.
Step 5: Organize the Interior
Once the hardware is in, sort your belongings into categories before placing them. Group like with like: shirts together, pants together, shoes on one ledge, accessories in bins. Give each category a defined zone, and label bins on the front edge so the contents are visible at a glance.
Leave about 10 percent of the storage empty for growth. A closet packed to the limit becomes disorganized quickly, and an open slot makes it easy to return items to their place. For more ideas on zoning a closet, see Ideas for Closet Organization: 12 Layouts and Systems That Work.
Common Mistakes to Avoid
- Measuring once and trusting the figure. Recheck width at three heights.
- Mounting the towers only into drywall. Use studs for any load-bearing point.
- Setting the rod too high for shorter garments, which wastes floor-to-rod space.
- Overloading the top shelves with heavy bins that are hard to reach safely.
- Skipping the level check, which causes drawers to bind and rods to sag.
- Filling every slot on day one, leaving no room for new items.
Tips for Long-Term Results
Review the closet every six months. Remove anything you have not worn or used in that time, and rotate seasonal items. If you find that one side is consistently overfull, shift a shelf or add a bin rather than forcing more into the same space. A system that is reviewed regularly stays usable far longer than one that is only set up once.
For a broader comparison of closet systems and how they handle different loads, you may also find Top 7 Walk In Closet Organization Systems with Drawers and Rods (2026) helpful. If your closet is especially narrow, Top 5 Small Closet Organization Systems Compared for Tight Spaces covers layouts that work in tight footprints.
Recommended gear
A few supplies make the installation more accurate and the finished closet easier to maintain.
- Digital stud finder helps you locate framing before drilling, which matters most for the tower anchors. View on Amazon
- Four-foot level lets you check both towers and the rod for plumb and level in one pass. View on Amazon
- Clear stackable storage bins keep small items visible and contained on open shelves. View on Amazon
FAQ
What width range does the adjustable system cover?
The system is designed to fit openings from about 72 inches to 120 inches. Measure the narrowest point of your closet and confirm the figure against the manufacturer’s specifications before purchase.
Can I install the towers into drywall only?
You can use wall anchors rated for the load, but anchoring into studs is more secure for any tower carrying significant weight. Where studs are not aligned, a spacer block helps bridge the gap.
How high should the hanging rod be?
A single rod for standard-length garments is commonly placed around 40 to 42 inches from the floor. A full-length rod is usually set near 66 to 70 inches. Choose the height based on what you store most.
Do I need two people to install it?
One person can assemble the parts, but a helper is recommended for standing up and holding each tower while it is leveled and fastened.
How do I know the towers are level?
Place a level on each shelf and on the rod after installation. Adjust the anchors or spacers until the bubble is centered in both directions.
Can the system hold heavy items?
Load capacity depends on the components and how they are anchored. Distribute heavier items on lower shelves and check the manufacturer’s stated limits. For any unusual loading, consult a qualified installer or contractor.
How often should I reorganize the closet?
A review every six months works well for most households. Rotate seasonal items at the same time to keep the interior current.
Conclusion
An easyfit dual tower closet organization system 72″-120″ adjustable width is a practical fit for closets that do not match standard sizes. Careful measuring, a planned layout and secure anchoring will do more for its performance than any particular accessory. Set it up in the order described, sort your belongings into zones, and review the closet twice a year to keep it working as intended.

